測量體溫
按測量按鈕打開探熱器，就會顯示啟動屏幕。確保探熱器處於身體模式。從上眉毛到探頭之間保持5cm到8cm的距離。按下測量按鈕，當它給出「嗶」聲代表測量完成，數值將會顯示。如果測量值超過警報值（默認值為37.5°C），它會發出4 次連續的蜂鳴聲作為指示。測量後，如果溫度計閒置10秒，則顯示“OFF”並發出「嗶」聲然後會自動關閉。
Body temperature
Press measurement button to turn on thermometer and it displays boot screen. Make sure the thermometer is under body mode. Keep distance at 5cm to 8cm from upper eyebrows to the probe. Press measurement button and when it gives a “beep” measurement is finished and value will be displayed. If measurement value is exceeding alarm value (Defaulted value is 37.5°C), it gives 4 successive beeps as an indication. After measurement, if the thermometer is idle for 10 seconds, it will display “OFF” and gives a “beep” and shut off automatically.
測量物體溫度
按測量按鈕打開探熱器。確保探熱器處於物體模式。從物體到測量探頭之間的垂直距離保持在5cm 到8cm。按下測量按鈕，然後它會發出「嗶」聲時，測量完成並顯示數值。測量後，如果溫度計閒置10秒，則顯示“OFF”並發出嗶嗶聲並關閉自動關閉。
環境溫度
按測量按鈕打開探熱器。確保探熱器處於物體模式。按下測量按鈕。當它發出「嗶」的一聲時，測量完成，數值將會顯示。
Object temperature
Press measurement button to turn on thermometer. Make sure the thermometer is under object mode. Keep vertical distance at 5cm to 8cm from object to measurement probe. Press measurement button and when it gives a “beep” measurement is finished and value will be displayed. After measurement, if the thermometer is idle for 10 seconds, it will display “OFF” and gives a beep and shuts off automatically.
Ambient temperature
Press measurement button to turn on thermometer. Make sure the thermometer is under object mode. Press measurement button. When it gives off a “beep”, the measurement is finished and value will be displayed.
| 問題 | 解決方法 |
| LCD屏幕顯示”Lo”或“Hi” | 微風﹑額頭上的水、汗液、化妝品等可能影響溫度測試；檢查偏差設置；如周圍環境溫度變化過大，或設備剛測量超高溫/超低溫物體，請將設備靜置10分鐘後再進行測量；設備距離測量物體應為5-8cm |
| 按下測溫按鈕後設備無反應 | 更換電池；檢查設備是否在菜單設置模式，當設備設置菜單時，不能測試溫度 |
| 屏幕無顯示或顯示錯誤 | 取出並再一次放入電池 |
| 無“嗶”聲 | 檢查聲音提示是否開啟 |
| 一開機設備自動關機 | 檢查電池電量或更換電池 |
| Mishap | Solution |
| LCD display “Lo” or “Hi” | Breeze, water, sweating, cosmetic on the forehead may affect measurement. If the environmental temperature changes enormously or if the thermometer is used directly from high temperature to very low temperature, the measurement difference will happen. The thermometer should be kept in a relative stable environment for 10 minutes to obtain heat balance before starting a new measurement. Ensure measurement distance is 5cm to 8cm. |
| No response when pressing measurement button | Take out and reassemble battery. Check if the thermometer is under menu setup. In procedure of menu setting, thermometer is unable to measure and therefore no response. |
| No or improper display | Take out battery and install battery again. |
| No beeper | Check if beeper is switched off. |
| Shut off right after switching on | Check battery level or take out and install the battery again |
你可能會喜歡的產品
最近留意的產品
- Opens in a new window.